Description

Preface 

This is the sixth edition of CSA M421, Use of electricity in mines , one of a series of Standards on mine safety. It supersedes the previous editions published in 2016, 2011, 2000, 1993, and 1985. The following significant revisions have been made to this edition: a) New Clause 4.3.1.5 introduces the requirements for protection of cables and conductors. b) New Clause 4.3.1.6 introduces the requirements for cable restraint. c) Clause 4.3.3.4.2 from the previous edition was revised and relocated to Clause 4.3.1.7 in this edition. The cable protection requirements of this clause now apply to all cables, not just portable power cables. d) Clause 4.3.3.2 from the previous edition was revised and relocated to Clause 4.3.1.8 in this edition. The splicing requirements are now made more general and apply to all cables, not just portable power cables. e) New Clause 4.3.4 introduces the requirements for armoured cables. f) Clause 4.4.1 from the previous edition has been reorganized and it is now presented as Table 4. g) New Clause 4.5.7 introduces an exception to the limit for ground-fault voltage. h) Clause 4.10 from previous edition was relocated to Clause 4.2.8 in this edition for clarity. i) New Clause 4.6.5 consolidates the requirements for transfer of potential from Clauses 5.3.3.3 and 6.8.3 from the previous edition. j) New Clause 6.2.2 introduces the consolidated requirements for pressurized gas insulated systems from transformer and switchgear sections. k) Clause 6.4.5 has been revised to remove gas-filled transformer requirements covered by the new Clause 6.2.2f or pressurized gas insulated equipment. l) Clause 6.6.2 has been revised to allow fluid at 275 °C or greater. m) Clause 7.6.2 has been revised to include a note to use test methods in IEEE 400. This Standard, used in conjunction with the Canadian Electrical Code, Part I, establishes minimum safety standards for the installation and maintenance of electrical equipment in mines or other mining applications requiring special consideration beyond the requirements of the Canadian Electrical Code, Part I. This Standard is not intended as a design specification nor as an instruction manual. In the preparation of this Standard, consideration has been given to the prevention of fire hazards and injury to persons and property, and to proper maintenance and operation. Due regard has been given to recognized codes and standards now in force. This Standard was developed by CSA Group with the funding support provided by the Canadian Association of Administrators of Labour Law — Occupational Safety and Health (CAALL-OSH), including provincial and territorial governments, as well as the Government of Canada. This Standard was prepared by the Technical Committee on Use of Electricity in Mines, under the jurisdiction of the Strategic Steering Committee on Occupational Health and Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. 

Scope 

1.1 Purpose 

This Standard establishes minimum requirements for electrical work and electrical equipment operating, or intended to operate, at a mine. Note: Users should be aware that federal, provincial, and territorial legislation can impose additional requirements. 

1.2 Application 

This Standard is supplementary to, or amendatory of, the requirements of the Canadian Electrical Code, Part I, as adopted by the regulatory authority having jurisdiction. Note: Adherence to the Canadian Electrical Code, Part I, normally addresses the minimum electrical safety requirements for mining-related fixed buildings, structures, and premises located on the surface, as these are no different from other industrial facilities. Such facilities could include processing plants, camps, offices, and drys. However, specific applications can exist within or on such buildings, structures, or premises that warrant the application of this Standard, such as supplies to mobile and movable equipment operated at voltages exceeding 150 V to ground. Examples of mine equipment operating at voltages exceeding 150 V to ground are a) mobile equipment fed by portable power cables; b) movable equipment fed by portable power cables or mine power feeders where the ground-fault voltage ground potential rise (GPR) relative to the surrounding earth or structures, and the transfer of these voltages, is required to be limited to tolerable touch voltage values; and c) quick-connect couplers.

1.3 Application to non-mining structures 

This Standard does not apply to tunnels, aqueducts, conduits, or excavations for civil construction purposes. However, where mines incorporate such structures, this Standard applies. 

1.4 Structure of this Standard 

Clauses 1 to 4 apply to all mines. The remaining clauses apply as follows: a) Clause 5 applies to surface mines and quarries and to the surface portion of underground mines; b) Clause 6 applies to underground mines; and c) Clause 7 applies to underground coal mines. 

1.5 Terminology 

In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Product Details

Edition:

6th

Published:

07/20/2023

ISBN(s):

9781488348167

Number of Pages:

108

File Size:

1 file , 1.4 MB

Product Code(s):

2430854, 2430854

Note:

This product is unavailable in Russia, Ukraine, Belarus